The ***ALL NEW*** AUSubaru.com.au Forums

I never measured tray to tank clearance. Haha. Also the size of the flanges is bigger than the top half of the tank is tall. I'll prob have to adjust / cut out and weld flat sheet to take out the top edge for the hoses to "fit" between the 2. Holley hydromat would be a far easier but more expensive ...

Before I bought the ********* front arm, I bought the correct angle taper cutter to re cut my / l series control arms for an ej balljoint. I never used it but dfoyl borrowed and used it. A kit? The only tools I have used are a 5" angle grinder, scribe, square, steel rule, and tape, cordless drill an...

********* L series arm, ej balljoint and hub, my tie rod ends and steering rack on the front. Factory my castor rods (cause I spaced back the crossmember 100mm) Xt6 rear hubs from the U.S. Custom modified (extra holes and washers welded around new holes) ej rear backing plates for hand brake. I orig...

Side note, any of the single range boxes out of gc8 rx Impreza are cable, with wrx gears and ratios. Gen 2 liberty 2.5 single range too.

El_Freddo wrote:And the MY auto sway bar apparently works with the EJ drivetrain as it's shaped differently.

Can verify this, with MY control arms. Pity the bar is drinking straw thickness.

Haha, yeh I was puckered up the first time I stuck the grinder into them. Even though they sat empty in the sun for a good 2 years and should have evaporated everything out, I stuck a hose in them for a good 1/2 hour and first cuts were when they were still full of water. Pump hangers and angles sho...

If you're going to this much effort why didn't you retro fit a gen 4 rear end in there? Main reason for not swapping in a gen 4 or even liberty / gc8 wrx rear end, was still a "weak" expensive diff and width. ( I have a clutch r160 centre already, cheap of import monster) too wide and the the only ...

Start bending tank for flanges http://uploads.tapatalk-cdn.com/20160423/f0faaae12cb00d0a7be222c4d547f8ec.jpg http://uploads.tapatalk-cdn.com/20160423/fe56e2dfaee93af8d655cf27d9e3459f.jpg http://uploads.tapatalk-cdn.com/20160423/e716f7cf772bafb89d7b7b133331cc0f.jpg http://uploads.tapatalk-cdn.com/201...

http://uploads.tapatalk-cdn.com/20160423/c8a3591cc568a29d409cacc9ee4ec08a.jpg http://uploads.tapatalk-cdn.com/20160423/9d403652200cbeec1b31324b63334c99.jpg http://uploads.tapatalk-cdn.com/20160423/cd62465819e2b87d7117a58e1323b8d6.jpg Weld in baffle, after making holes for clearances on important th...

http://uploads.tapatalk-cdn.com/20160423/b9c468878aed22d3d097e41b35b33fc4.jpg Cut holes for mounting flanges. Drink more beer and think of way to fit flanges for clearance of jet filler and hoses without having to space down tank and then all suspension as well http://uploads.tapatalk-cdn.com/20160...

Can someone change the title to efi please haha Anyway, 2 weeks later http://uploads.tapatalk-cdn.com/20160423/187f39301fad070d2eaf1dc89aef5481.jpg http://uploads.tapatalk-cdn.com/20160423/d8a85f8c01717b19703b1b9b2f7c3acf.jpg http://uploads.tapatalk-cdn.com/20160423/6e0783f85af2b91a58feb304966ededb....

So I was in the process of converting my brumby to ej22 out of a g1s1 liberty. Plenty of time (working as a builders labourer) not much cash and an ounce of skill. And heaps of parts from various failed projects (scope growth) Conversion needs efi fuel pump, have 2 x brumby fuel tanks (1 had a homem...

At this stage, I was feeling pretty good with myself. Planning weekends to work on ute around surf boat carnivals, figured a decent push over next 2 months, I'd have the rear end and fuel tank project finished and get the rust repairs and re spray done over Christmas break. Then the Wrx engine saga ...

Huh, Appears to be correct http://uploads.tapatalk-cdn.com/20160423/7f46d5d0410c070dbcb86a5e2027d8a1.jpg Get grinder out again then centre it all http://uploads.tapatalk-cdn.com/20160423/7d1cd85063292736a9fa2341e01f969b.jpg http://uploads.tapatalk-cdn.com/20160423/1cba49ebbfe809144d789f292c8b29b3.jp...

Attempt 2

So I don't know what happened there to triple post the same photo http://uploads.tapatalk-cdn.com/20160423/2c39744d035a3ac1fb098b6bec3fba21.jpg http://uploads.tapatalk-cdn.com/20160423/de50fc1b4fb07df3cfdf6f92f71a3005.jpg Test fit on jig http://uploads.tapatalk-cdn.com/20160423/4faebbb81d4bfb5df7883...

Started making some mounts out of left over 6mm 50x100 rhs http://uploads.tapatalk-cdn.com/20160423/a7d5c501823769e9d5359abe0acd2fc9.jpg http://uploads.tapatalk-cdn.com/20160423/bf763d85968501baa983945bef4d4c8c.jpg http://uploads.tapatalk-cdn.com/20160423/c8e024e2990e78f108e4e7270a0c5368.jpg http://...

Procrastinate some more. Cut stuff with a grinder http://uploads.tapatalk-cdn.com/20160423/829b1348014ea2a6892a2d4464ccd9fb.jpg Get it square and even http://uploads.tapatalk-cdn.com/20160423/55d03a7a60e301c08fee5043d6b210b9.jpg Level, trying to over think things by changing changing pickup points h...

L series crossmember http://uploads.tapatalk-cdn.com/20160423/1ad2eb9b855fe7c20a161fcebd6dbad8.jpg Hmm http://uploads.tapatalk-cdn.com/20160423/dbe47e91b76a5829d66521f6327ad67b.jpg That explains why it won't bolt up http://uploads.tapatalk-cdn.com/20160423/10f8fd89d6e86771b67664f86b380b65.jpg Note t...

Caution: Novel ahead So it's raining and I'm procrastinating on doing some bookkeeping, thought I'd share since i couldn't find anything similar anywhere on the web I'm building a street car out of a brumby. I still own a Wrx that was mildly modified at various stages. 257 with cp's, vf34, 3" exhaus...