What did you do to improve your soobie today
- Silverbullet
- Senior Member
- Posts: 2878
- Joined: Mon Aug 23, 2010 6:20 pm
- Location: Adelaide
Bolted the L series splined hubs to the MY discs, then there was no problem. You were right about the L series splined hubs having a shorter splined section, but the turned parallel section is a larger diameter so it clears the extra long splined section of the MY drive shaft anyway.steptoe wrote: You say L discs don't fit front of MY, so how'd you fit the rims to front to show us?
Will it ever end!?
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end
I'm not sure why Lseries control arms are getting mentioned here, the MY and L series ball joint receptacle is the same.
I'm not criticizing what you have done Silverbullet, I'm glad you made it work, but why don't you put the Lseries (vortex) knuckles on and you can use the nice front brakes too?
I'm not criticizing what you have done Silverbullet, I'm glad you made it work, but why don't you put the Lseries (vortex) knuckles on and you can use the nice front brakes too?
The trading corner : the stuff that I need ATM -
# Vortex Main Dash Surround / Bezel ANY COLOUR,
# Vortex Radio, # RHD Vortex 4speed auto digital dash,
# RH-Side parking (86+) Vortex wiper transmission,
# EA82 AWD 4EAT,
If you have them please PM me
# Vortex Main Dash Surround / Bezel ANY COLOUR,
# Vortex Radio, # RHD Vortex 4speed auto digital dash,
# RH-Side parking (86+) Vortex wiper transmission,
# EA82 AWD 4EAT,
If you have them please PM me
- Silverbullet
- Senior Member
- Posts: 2878
- Joined: Mon Aug 23, 2010 6:20 pm
- Location: Adelaide
The Vortex/L series knuckles have a different camber angle built into them because the L series has a wider track width. If I used L series knuckles with MY control arms the positive camber would be crazy like this = \ _ / So to remove this I would need to use L series control arms which are longer, this would also increase the track width at the front of my car. I will think about it some more and decide if I want to go down this path, because as Jonno says above I would also then need L series drive shafts, longer radius rods (Well I'm getting some custom made anyway so no big deal there) and also the front sway bar ends probably wouldn't line up any more.nncoolg wrote:I'm not sure why Lseries control arms are getting mentioned here, the MY and L series ball joint receptacle is the same.
I'm not criticizing what you have done Silverbullet, I'm glad you made it work, but why don't you put the Lseries (vortex) knuckles on and you can use the nice front brakes too?
But it would have a meaner stance
Will it ever end!?
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end
I reckon if you put them on it would surprise you.
I had l series front stuff on my MY touring wagon and it was sweet.
Remember the strut towers in an l series would be further apart aswell, they wouldn't have just made the control arms longer.
Actually I'm going out in a limb here and guessing the control arm length would be very similar, with just the chassis rails wider in the later model (L & XT) series, BUT THIS IS A GUESS!!!
Perhaps we should start a new thread for this, instead if loading up this accomplishment one?
I had l series front stuff on my MY touring wagon and it was sweet.
Remember the strut towers in an l series would be further apart aswell, they wouldn't have just made the control arms longer.
Actually I'm going out in a limb here and guessing the control arm length would be very similar, with just the chassis rails wider in the later model (L & XT) series, BUT THIS IS A GUESS!!!
Perhaps we should start a new thread for this, instead if loading up this accomplishment one?
The trading corner : the stuff that I need ATM -
# Vortex Main Dash Surround / Bezel ANY COLOUR,
# Vortex Radio, # RHD Vortex 4speed auto digital dash,
# RH-Side parking (86+) Vortex wiper transmission,
# EA82 AWD 4EAT,
If you have them please PM me
# Vortex Main Dash Surround / Bezel ANY COLOUR,
# Vortex Radio, # RHD Vortex 4speed auto digital dash,
# RH-Side parking (86+) Vortex wiper transmission,
# EA82 AWD 4EAT,
If you have them please PM me
- Silverbullet
- Senior Member
- Posts: 2878
- Joined: Mon Aug 23, 2010 6:20 pm
- Location: Adelaide
- Silverbullet
- Senior Member
- Posts: 2878
- Joined: Mon Aug 23, 2010 6:20 pm
- Location: Adelaide
Finally got around to putting a new clutch cable in the Brumby today. It's been sitting there for months now, waiting for me to build up the enthusiasm to do the job. Last time I tried it was a disaster, had bought the wrong cable and ended up putting the old one back. This time I attacked it with a plan but it is still a huge PITA The cable type with two big washers, rubbers, and a spring clip to clamp it all together. I'm convinced the only way to do it is to take the pedal box out, which is what I did. Now it feels like there's nothing there, unlike the leg ache inducing old cable.
Will it ever end!?
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end
Tow bar!
Fitted a new tow bar, well not actually new. It was the original supplied with the car. I had the bar itself galvanized, the tongue powder coated, the ball re-chromed and replaced any fasteners that were beyond re-plating. Also found a nice rubber cover for the ball when not in use.
The wiring and connector are fine so nothing to do there. If you do a lot of beach driving or putting boats in or out of salt water, galvanizing is the go!
The wiring and connector are fine so nothing to do there. If you do a lot of beach driving or putting boats in or out of salt water, galvanizing is the go!
- steptoe
- Master Member
- Posts: 11582
- Joined: Thu Oct 06, 2005 10:00 am
- Location: 14 miles outside Gotham City
went a little closer to turbo in an MY ...... marke out the engine cross member where most would cut a gaping hole for exhaust to clear it. Thought a little harder, cut along the front top edge, and another through the middle , making 4 rough sized quarters out of a rough circle.
Using a biggish hammer, no heat, belted the shape I wanted, test fit or two bits overlapping each other, and a V shaped gap where things had to spread apart between the 'quarters'
and then off to a certified welder/boiler maker with some credit up my sleeve
Left him alone for a little while and shazam no new metal fabricating required, with minimal cuts - and a hole welding trick I learned today (place non ferrous lump below hole and fill)
Welded top side and underside - strong enough even for EJ turbo power and job stamped with his certifying numbers right below.
This should impress a certifying engineer more than my novice welding. Have heard of some engineers rejecting any approval on some off-shore sourced welding rods.
Time to scrub a dub dub it and some new paint
Using a biggish hammer, no heat, belted the shape I wanted, test fit or two bits overlapping each other, and a V shaped gap where things had to spread apart between the 'quarters'
and then off to a certified welder/boiler maker with some credit up my sleeve
Left him alone for a little while and shazam no new metal fabricating required, with minimal cuts - and a hole welding trick I learned today (place non ferrous lump below hole and fill)
Welded top side and underside - strong enough even for EJ turbo power and job stamped with his certifying numbers right below.
This should impress a certifying engineer more than my novice welding. Have heard of some engineers rejecting any approval on some off-shore sourced welding rods.
Time to scrub a dub dub it and some new paint
- steptoe
- Master Member
- Posts: 11582
- Joined: Thu Oct 06, 2005 10:00 am
- Location: 14 miles outside Gotham City
WOW ! Powers of the 'net ! It does help to see how others have done it, rather than read how ..... never really thought how a preprepared section of pipe or tube could look in this application until now. Won't look like yours unless I can find some paint I have my mind on ..... a tin of black gloss circa 1991 or the one from KBS coatings for this kind of job
Is that a crumple zone cut in the bottom front of the mod ?
Is that a crumple zone cut in the bottom front of the mod ?
- Silverbullet
- Senior Member
- Posts: 2878
- Joined: Mon Aug 23, 2010 6:20 pm
- Location: Adelaide
After a long drive on the weekend (some 500 odd highway k's) and some of the worst corrugations I've ever seen (big enough to get bogged in!) the Brumby has been making a few odd noises, one front CV is clicking away around every corner and there was a brake rubbing noise. Then today the brake noise got really really bad in one of the rear drums, was afraid to use the brakes because of the grinding/screeching noise and found myself pulling up at lights with the hand brake only
So just now whipped the rear drum off to find one of the return springs (the smaller one) from the brake shoes rattling around loose inside the drum, a spring shaped imprint in the steel casing of one of the brake shoes, and the whole insides covered in metal shavings and cast iron dust :( Needless to say the drum is nothing but grooves now, not sure there's enough material to machine them out either. Are new drums even available?? Either way, I'll get some new shoes and borrow a mates lathe in the next week or so to see if they clean up. They're already 181.3mm, service limit is 182mm
Oh how nice it would be to stumble upon another set of rear discs
So just now whipped the rear drum off to find one of the return springs (the smaller one) from the brake shoes rattling around loose inside the drum, a spring shaped imprint in the steel casing of one of the brake shoes, and the whole insides covered in metal shavings and cast iron dust :( Needless to say the drum is nothing but grooves now, not sure there's enough material to machine them out either. Are new drums even available?? Either way, I'll get some new shoes and borrow a mates lathe in the next week or so to see if they clean up. They're already 181.3mm, service limit is 182mm
Oh how nice it would be to stumble upon another set of rear discs
Will it ever end!?
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end
- Silverbullet
- Senior Member
- Posts: 2878
- Joined: Mon Aug 23, 2010 6:20 pm
- Location: Adelaide
Well yes, but you have to find a set that is for sale first, they don't come up too often and go up in price every timesublime wrote:Stumble? I seem to have to cough up $$$$ for them!:)
Doug, yes I do have 2 spare drums but they've been machined at least once in the past as well. I'll choose the best of the bunch with the most material left in it.
Will it ever end!?
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end