Sloppy Shift in my MV/Brumby....
- sholinguteman
- Junior Member
- Posts: 43
- Joined: Tue Nov 23, 2010 4:14 am
- Location: Deep South of Ampshire , England
Sloppy Shift in my MV/Brumby....
Hello there , could somebody point me in the direction of the "how to" page that relates to replacing the bits that cure the Brumbies sloppy shift problem. I have the bits that are still available but cannot find that page which I am sure was on here ? thanks "MO"
- sholinguteman
- Junior Member
- Posts: 43
- Joined: Tue Nov 23, 2010 4:14 am
- Location: Deep South of Ampshire , England
Ok I found it , but unfortunately the photos have been deleted , still here tis...
showthread.php?t=18767
showthread.php?t=18767
- Silverbullet
- Senior Member
- Posts: 2873
- Joined: Mon Aug 23, 2010 6:20 pm
- Location: Adelaide
D'oh Pictures are gone againsholinguteman wrote:Ok I found it , but unfortunately the photos have been deleted , still here tis...
showthread.php?t=18767
Anybody who tells you any pic you post on the internet is there forever is telling you dirty lies!
Will it ever end!?
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end
- sholinguteman
- Junior Member
- Posts: 43
- Joined: Tue Nov 23, 2010 4:14 am
- Location: Deep South of Ampshire , England
- FROG
- General Member
- Posts: 1409
- Joined: Fri Feb 23, 2007 12:41 pm
- Location: UNDER THE SOUTHERN CROSS GRIFFITH NSW
- Contact:
That was a very long time ago MO !!sholinguteman wrote:Thanks for that SILVERBULLET. Good description and easily done. And thanks to FROG for supply the bits to me a L O N G time ago LOL And what a difference it made , No more spoon in bowl of custard guess what gear your in syndrome . Highly recommended "MO"
GRAB THE VIN FROM DONOR VEHICLES
AUSubaru member specials
Brumby EA81 Oil Pump kit (4 x 'o'rings + gasket) posted Australia wide $22!
Brumby sloppy shifter bush kit $44 posted
email me
http://www.domsmotors.com.au
NOW DISTRIBUTING FOR SUBAXTREME BASH PLATES, NUDGE AND BULLBARS
- sholinguteman
- Junior Member
- Posts: 43
- Joined: Tue Nov 23, 2010 4:14 am
- Location: Deep South of Ampshire , England
Yes believe it or not ... I traded the truck to Giles a couple/few years ago. And he passed it on , it went through a couple of hands and then turned up on ebay so...... I bought it back again and then replaced the bushes lol. Quick question ... I dont think that the bushes had ever been done ? and when I took it apart there was no bottom cup (part no 42 ? ) but there was a bit not shown or numbered in your diagram. Its a tube of thin white plastic with a split in it. The tube is about an inch long . when the O ring (part 4) is fitted to the bottom of the gearstick , this then fitted /slid down in to the above mentioned plastic tube. It seems to work as there is then no "slop" or movement in the bottom. I was wondering .... had somebody knocked this up themselves or was this a later mod ? (my truck is a 94. built in 92 ) Unfortunately I did not take any photos before I re assembled it. Are all those bits still available ? thanks "MO"FROG wrote:That was a very long time ago MO !!