Page 2 of 3
Ea82t
Posted: Fri Jun 12, 2015 10:47 am
by legacytt
This could be the answer to your engine sourcing issue.
http://www.gumtree.com.au/s-ad/north-bo ... 1080939096
I know some people here who used to rally one of the original 5 RX Turbo's imported in '85. they were forever replacing the dual range gears as these were the weak link. So a vortex single range box would be the go, or put liberty gearset and rear transfer in L series case.
Posted: Fri Jun 12, 2015 11:09 pm
by wagonist
I've just sent that guy a message asking what gearbox is included.
I've got a Vortex single range full-time 4wd box in my car currently, but I'd prefer the dual range full time box (mainly cos I've got RX turbo black interior trim & the centre console looks wrong
).
If it's the right box, I do you a deal on mine with this engine?
Posted: Fri Jun 12, 2015 11:25 pm
by El_Freddo
legacytt wrote: So a vortex single range box would be the go, or put liberty gearset and rear transfer in L series case.
For an EJ AWD in EA cases right? Just want to make sure this is what you're trying to say as you can't mix AWD stuff with PT4wd stuff.
wagonist wrote:I've just sent that guy a message asking what gearbox is included.
I've got a Vortex single range full-time 4wd box in my car currently, but I'd prefer the dual range full time box (mainly cos I've got RX turbo black interior trim & the centre console looks wrong
).
Why not build a dual range box with an EJ dual range set of gears, EA or EJ cases (which ever you need to use) and the AWD centre locking diff out the back? Easiest way to convert the single range to dual range
Cheers
Bennie
Posted: Fri Jun 12, 2015 11:32 pm
by El_Freddo
And the box to me looks like a PT4wd - no vacuum diaphragm in the pic and from what I can tell no bulge below rear output shaft for the centre diff.
But the engine looks schmick for this rally car
Probably wrong timing though, I know how projects like this go!
Cheers
Bennie
Posted: Sat Jun 13, 2015 1:41 pm
by legacytt
El_Freddo wrote:For an EJ AWD in EA cases right? Just want to make sure this is what you're trying to say as you can't mix AWD stuff with PT4wd stuff.
Yes use the EA case but put all the gearset from EJ box in and then bolt the viscous centre rear housing on. Would need new Xmember and tailshaft but would make a good combo.
Posted: Sat Jun 13, 2015 8:13 pm
by rally-leone
legacytt wrote:This could be the answer to your engine sourcing issue.
http://www.gumtree.com.au/s-ad/north-bo ... 1080939096
I know some people here who used to rally one of the original 5 RX Turbo's imported in '85. they were forever replacing the dual range gears as these were the weak link. So a vortex single range box would be the go, or put liberty gearset and rear transfer in L series case.
This looks great. Ive sent the guy a message, cheers.
No current updates as I've been flat out ayat work and haven't had a weekend since my first post.
suspension
Posted: Sun Jun 14, 2015 7:25 am
by rally-leone
Does anyone know of a place in Sydney that reconditions shock absorbers and what sort of price ill be looking at to get them done.
I noticed the car was looking a little droopy when I was in the yard last night...
Also if anyone has some new front lower control arm ball joints and a set of gearbox mounts laying around in Sydney ill happily buy them off you over getting some from super cheap...
cheers
josh
Posted: Sun Jun 14, 2015 10:06 am
by steptoe
new ball joints RP257? repco and others cheap as 25 bucks ??
I would have some L gearbox mounts
do you know how to send me a PM ?
Posted: Sun Jun 14, 2015 12:37 pm
by FujiFan
I noticed the car was looking a little droopy when I was in the yard last night...
More likely to be the springs causing this. And are you speaking of front or rear or overall?
J.
Posted: Sun Jun 14, 2015 4:26 pm
by rally-leone
FujiFan wrote:More likely to be the springs causing this. And are you speaking of front or rear or overall?
It only sags on the drivers side front and rear and only after being stretched out (suspended on the hoist). it sits fine for a while after that.
it has rally style coil overs all round.
AS for the EA82T engine on gumtree, I spoke to the guy (Tony, who seemed to be a very nice older gentleman that knew what he was talking about) about it today and unfortunately he has someone flying up tomorrow to check it out, but if the add is still up on Tuesday ill give him a call back
(he also has a turbo brumby up for sale if anyone is interested $6500 looks very well put together)http://www.gumtree.com.au/s-ad/north-bo ... 1080947325
Posted: Mon Jun 15, 2015 12:37 am
by FujiFan
It only sags on the drivers side front and rear and only after being stretched out (suspended on the hoist). it sits fine for a while after that.
Its prob nothing to worry about. If you have the time you could pull all struts out dismantle and measure spring free length and check dampers for leakage etc. But that is a pain in the proverbial.
it has rally style coil overs all round.
Sweet.
Does anyone know of a place in Sydney that reconditions shock absorbers
If they are serviceable/rebuild-able and they need it why not. The only place that comes to mind is Heaseman Steering which I believe are in Tempe
Also if anyone has some new front lower control arm ball joints and a set of gearbox mounts laying around in Sydney
Ive just assembled the new ball joints into my L, D'oh. I do have used G/box mounts, but not sure if I am willing to part with until I can source some more. Double D'oh.
And the box to me looks like a PT4wd - no vacuum diaphragm in the pic and from what I can tell no bulge below rear output shaft for the centre diff.
But the engine looks schmick for this rally car Probably wrong timing though, I know how projects like this go!
+1
J.
Posted: Mon Jun 15, 2015 6:18 am
by rally-leone
Its prob nothing to worry about. If you have the time you could pull all struts out dismantle and measure spring free length and check dampers for leakage etc. But that is a pain in the proverbial.
Suspension plays a big role (pun intended ) when it comes rally so anything i can do to have it at its best i will..
Ive just assembled the new ball joints into my L, D'oh. I do have used G/box mounts, but not sure if I am willing to part with until I can source some more. Double D'oh.
Im happy to get the ball joints from repco (anything i can get from a forum member that helps them out is better in my opinion ). As for the gearbox mounts i should have been more specific..
Im only after the 4 rubber mounts with the large retaining washers and bolts.
Posted: Tue Jun 16, 2015 6:04 pm
by rally-leone
This saturday i will be picking up my new engine.
I wont be needing everything on it. I.e. wiring loom, ecu, a/c pump, power steering pump, potentialy gearbox, rear disc set up, rear diff center. And what ever else i get off the guy while im there... (hes doing a clean out) so if you are after anything let me know
Posted: Wed Jun 17, 2015 7:05 pm
by El_Freddo
Nice score on the engine!
Could be interested in rear discs and rear diff if an LSD. Price dependant of course
Cheers
Posted: Thu Jun 18, 2015 1:39 pm
by rally-leone
El_Freddo wrote:Nice score on the engine!
Could be interested in rear discs and rear diff if an LSD. Price dependant of course
Cheers
How much are they worth?
Posted: Fri Jun 19, 2015 8:39 am
by steptoe
depends on completeness, whether 2WD or (4WD have splines etc) making more valuable, condition...seen go from 250 to 600
picked up the engine!
Posted: Mon Jun 22, 2015 6:28 pm
by rally-leone
Posted: Mon Jun 22, 2015 9:52 pm
by wagonist
ok, so that was PDQ getting the engine swapped over
Did the guy have any other stuff left over? I'm heading up that way this weekend?
Posted: Fri Jun 26, 2015 11:54 pm
by El_Freddo
rally-leone wrote:How much are they worth?
No doubt more than I could afford!
The LSD probably $400-$600
Rear discs, hubs, calipers, backing plates and brake lines probably $400+ as well provided they're the 4wd set (which I'm sure your rally car would be 4wd!).
You must have some time on your hands to turn that around so quickly!
Cheers
Bennie
Posted: Sat Jun 27, 2015 12:26 am
by FujiFan
I want that set of timing belt covers. They look pristine like some of the other bits on that score of a donor engine you got
So as for performance and longevity, do you plan to provide for an intercooler or water/meth inj setup? Or will this be a by the book period rally car?
J.