Brumby EJT project help Unknown parts?

Insane · Post by **Insane** » Mon Feb 24, 2014 7:03 pm

OK, Got excited and made another rookie mistake... When starting work on an unfamiliar motor always check it turns over by hand. Even had it off the stand and the new flywheel and box on...

The quote, "You're a god damned genius Gump!" comes to mind.

It was frozen but with a little oompf it now turns abot 180 degrees. Thinking it has either a frozen valve (its humid in bundy and has been sitting possibly 2 years) or the guy who owned it, an apprentice at bundy subaru, made a mistake putting on a new timing belt... Tomorrows adventure now though. Beer and a zombie movie are in order...

Post by **TOONGA** » Mon Feb 24, 2014 9:43 pm

From what you are describing it is possible that the motor has siezed at some point and will probably need to be rebuilt.

TOONGA

Insane · Post by **Insane** » Thu Feb 27, 2014 8:19 pm

turns out the spark plugs were only in 2 turns... So over the last 3 years of sitting in bundy (two floods) the humidity has got to the inside wear faces of the engine and given them a nice coating of oxide dust/rust The bores look ok after turning it over and the vlave seats i can see through the plug holes look ok too. (except for the orange colour) Am about to order a full gasket kit and when i pull it down, rings and give it a freshen up... Cam faces etc all look like new.

RSR 555 · Post by **RSR 555** » Thu Feb 27, 2014 9:10 pm

Yeah.. if that water has got inside and it's been sitting for a while, I'd recommend a rebuild. Sounds like it's going to be a big project car. We want pics along the journey

Insane · Post by **Insane** » Sat Mar 22, 2014 8:26 am

So I lost a little time on the brumby fixing a mates off road buggy... Back to it now.

I have since had delivered a full gasket kit for the EA and a manual that supposedly covers all 1.6 - 1.8 motors from 79 to 94.. Unfortunately no mention of the turbo version.

My question is, Are there any tolerance differences between turbo / non turbo? piston sizes the same? ring size and type?

Insane · Post by **Insane** » Tue Apr 22, 2014 7:11 pm

Have now stripped the EA82T down to a short block. everything is full of sludge and surface rust. Thankfully no damage to the bores just the faintest score marks from forcing it to turn over. Having stripped a few motors before I am thinking this one has very low kms. original bore size, no lip whatsoever, cam faces are all like new... Only Issue is that whoever first owned it didn't believe in coolant and all the water jackets are full of dust and crud. Bit worried about re-tensioning some of the head bolts in the water jackets back up. Should be ok though. Anyone know the part no for rings on an EA82T? I want to disassemble, clean and reassemble as I go...

YouTube · Post by **El_Freddo** » Tue Apr 22, 2014 9:52 pm

I'm wondering if we could get a Mod to change the title to "Brumby EA82T..." as I get excited with the "Brumby EJT..." title.

Don't get me wrong, I enjoy reading where you're going with this build, just that when the title pops up in my email updates I'm basically keen as mustard to read another EJt Brumby build

Cheers

Bennie

Insane · Post by **Insane** » Wed Apr 23, 2014 6:41 am

Yeah, I was thinking that when I went to post... If this motor turns out to be cactus during the rebuild or once in, too slow, I'll still go the ej option but maybe another project section is better for now.

Insane · Post by **Insane** » Fri Oct 17, 2014 3:45 pm

Hey guys. done nothing on this car for months. got to clean the garage though. anyone interested in the EJ18 / EJ22 SOHC turbo setup?

steptoe · Post by **steptoe** » Fri Oct 17, 2014 7:04 pm

El_Freddo wrote:I'm wondering if we could get a Mod to change the title to "Brumby EA82T..." as I get excited with the "Brumby EJT..." title.

Might explain why I don't recall seeing this thread - it started on EJ

Insane · Post by **Insane** » Sun Mar 08, 2015 12:42 pm

whole project is for sale. Everything including car and new parts. Will post for sale add in appropriate section in a moment. Would rather sell complete project but will consider selling parts if there's no interest. open to offers but was thinking maybe $2000 for the lot?