'92 Brumby resto w/ '84 wagon for parts
Cheers Freddo.
I read your thread, my welch plugs were no where near as bad luckily!
How does the cylinder get full of watery oil if the head gasket is fine? I get that the welch holes allow the stuff to mix but how does the stuff get in there?
I'll definitely replace the welch plugs in the other head, they're probably in much the same condition though I haven't looked yet. I pulled the spark plugs out of it and didn't see any water/oil on the plug like the other head. Maybe if I got a long cotton tip and put it in there I'd find evidence of it if it's in there.
I'll do the plugs in the short block too since the whole cooling system is really corroded; I'm guessing the guy who owned it used plain water instead of coolant. The spare engine that's in pieces is really handy for finding things like the location of the welch plugs, the spare head is also holding all my rockers/pushrods etc in order.
I read your thread, my welch plugs were no where near as bad luckily!
How does the cylinder get full of watery oil if the head gasket is fine? I get that the welch holes allow the stuff to mix but how does the stuff get in there?
I'll definitely replace the welch plugs in the other head, they're probably in much the same condition though I haven't looked yet. I pulled the spark plugs out of it and didn't see any water/oil on the plug like the other head. Maybe if I got a long cotton tip and put it in there I'd find evidence of it if it's in there.
I'll do the plugs in the short block too since the whole cooling system is really corroded; I'm guessing the guy who owned it used plain water instead of coolant. The spare engine that's in pieces is really handy for finding things like the location of the welch plugs, the spare head is also holding all my rockers/pushrods etc in order.
- steptoe
- Master Member
- Posts: 11582
- Joined: Thu Oct 06, 2005 10:00 am
- Location: 14 miles outside Gotham City
the guys in US use a thick piece of glass ~6mm or more, bond a sheet of wet and dry of grade of your choice, hit it with spray oil lube and circular motion to face the heads. Tried it myself and happy Watery oil, fondly known as buttermilk after coolant and oil been mixed with heat and oil pump pressure can and will get caught up in the PCV lines and rebreathed to cylinders
I had another case of rain water in sump up to the level of the bottom of the turbo , sat about at least six months , thought motor would be stuck shut - yet turned freely ! I guess if it had evaporated out then it would have rusted. May never get it running though ...
Yes, donk is not just a character in Croc Dundee
I had another case of rain water in sump up to the level of the bottom of the turbo , sat about at least six months , thought motor would be stuck shut - yet turned freely ! I guess if it had evaporated out then it would have rusted. May never get it running though ...
Yes, donk is not just a character in Croc Dundee
Haha, it's been ages since I've seen the croc dundee movies.
When I drained all the buttermilk out of the sump about 1L of water came out first.
Ordered parts yesterday; head gasket, welch plugs + a few filters and things to make up the amount which qualified for free shipping.
Until they arrive I'll probably focus on the daily drive; a 96 camry wagon which needs the attention that's been lost to the brumby.
When I drained all the buttermilk out of the sump about 1L of water came out first.
Ordered parts yesterday; head gasket, welch plugs + a few filters and things to make up the amount which qualified for free shipping.
Until they arrive I'll probably focus on the daily drive; a 96 camry wagon which needs the attention that's been lost to the brumby.
Back home again and had more of a chance to look at it.
I noticed that a steel pipe attached by a hose to the water pump was rusted out, so I pulled off a few more things to see how bad the corrosion was. Here's the lower radiator hose connects to the water pump:
There was also a heap of the stuff in the top hose.
I'm concerned how bad it might be inside the block, I'm thinking I'll definitely have to replace the bigger welch plugs that are there.
I'm once again leaning towards using the wagon engine. What do you guys reckon?
I noticed that a steel pipe attached by a hose to the water pump was rusted out, so I pulled off a few more things to see how bad the corrosion was. Here's the lower radiator hose connects to the water pump:
There was also a heap of the stuff in the top hose.
I'm concerned how bad it might be inside the block, I'm thinking I'll definitely have to replace the bigger welch plugs that are there.
I'm once again leaning towards using the wagon engine. What do you guys reckon?
Done the valve clearances and it still ticks. Going to have to wait until someones around to give me a hand with the compression tester.
I put up a video of the engine running on the facebook brumby group so you guys can hear the ticking. You won't need to have Facebook to view it, just follow the link.
https://www.facebook.com/tim.dyson.12/v ... 331268050/
I put up a video of the engine running on the facebook brumby group so you guys can hear the ticking. You won't need to have Facebook to view it, just follow the link.
https://www.facebook.com/tim.dyson.12/v ... 331268050/
Apparently it's rod knock. I don't have the facilities to rebuild engines sadly. Dad has a new workshop in planning for the farm, hopefully sometime this year. So looks like the project will be on hold for now.
I've taken my camry off the road recently, so I'm going to be on the look out (and saving $) for a roadworthy (or close) brumby or MY/L series wagon to replace it. Luckily the family's got a spare Magna that I can use pretty much indefinitely.
I've taken my camry off the road recently, so I'm going to be on the look out (and saving $) for a roadworthy (or close) brumby or MY/L series wagon to replace it. Luckily the family's got a spare Magna that I can use pretty much indefinitely.
- Silverbullet
- Senior Member
- Posts: 2876
- Joined: Mon Aug 23, 2010 6:20 pm
- Location: Adelaide
Definitely not a healthy noise seems to loud and low pitched to be valve train noise. I've heard similar on one of my own engines years ago which turned out to be a failed main bearing.
Will it ever end!?
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end
-EA81 TWIN CARB!!!!
-L series 5 speed
-Custom paint job
-2" lift
-Full custom re-wire
-L series front end